THERMADOR Error Code E14
Professional Ranges Models: PDR30/36/48…PRG30/36/48
ERROR CODE | DESCRIPTION | RESOLUTION |
CODE E14 | Turn the clock selector knob to Off Adjust the oven control by turning the clock selector knob slightly to the left (counter clockwise). This may stop the flashing message/beeping and clear the display window | Latch switch problems |
The control continually keeps track of system specifications for control and oven failings and reports a mistake code when a system problem is spotted. The control utilizes the ovens blue “on light” as well as oven “heating light” to report an identified fault code. The control will remain to blink the lights in the appropriate series as long as the mistake exists.
Detection of a fault does not impede the capability of the control to remain to function if the mistake is not critical for the desired procedure. For instance: If the range door lock is faulty, the range will remain to cook because the mistake would only protect against the range from self-cleaning.
HOW TO INTERPRET CODES
When a fault happens, the control will flash heaven stove “on light” and also heaven “heating light” sequentially to indicate the fault. The mistake codes have two numbers, these numbers are interpreted by the variety of times the lights flash. The stove “on light” will certainly flash showing the very first number, and the “home heating light” will flash indicating the second number.
INSTANCE:
Error E9 is … No Cooling Followers. The code is 43. The oven “on light” will certainly flash 4 times, then the “heating light” will flash three times, after that pause. The series will then duplicate as long as the fault exists.
ERROR CODES FOR OVENS WITH DREEFS CONTROL
The adhering to graph shows the mistake codes that can be displayed in the Oven/Selector home window throughout specific oven malfunctions. A few of the mistake messages can be removed by performing the following steps:
- Turn the selector knob to OFF
2.”Modify” the oven by turning the selector knob somewhat to the left (counterclockwise). This may stop the blinking message/beeping and clear the window. - For mistakes E1, E9, E11, E12 as well as E13, the power supply going to the also must be shut off temporarily, and back on again.
- If an error stays displayed when the selector switch is OFF, and also after attempting to get rid of the display screen, as shown in actions 2 and 3, shut off the power going to the stove, and also refer to the chart below to assist you find the problem.
ERROR MESSAGE | ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
E1 | C&E | Control board problem. |
E2 | G&K | Cook or Clean mode runaway (temp >635 °F) Clean mode runaway (clean temp +32 °F). |
E3 | A&H | Open oven temperature sensor (>5000 Ω). |
E4 | A&H | Shorted oven temperature sensor (<5000 Ω). |
E5 | K&D | Control board too cold, too hot, or defective. |
E6 | C&J | Control board problem. |
E7 | A&I | Illegal temperature display. Turn off oven and try again. |
E8 | A&D | Control board problem. |
E9 | A&E | Latch switch problem. |
E10 | B&D | Control board problem. |
E11 | A&F | CT oven – latch switch problem |
E12 | A&E | CT ovens – latch switch problem |
E13 | A&C | CT ovens – latch frozen or no power to latch motor. CMT ovens – control board not converted (refer to page 3-7 for conversion data). |
E14 | A&E | Latch switch problem. |
E15 | B&D | Control board problem. |
ERROR CODE NOTES | DESCRIPTION OF PROBLEM |
A | Turns heat off on the failed oven only; microwave not affected. |
B | Turns all heat off; microwave not affected. |
C | Disables the CLEAN mode in both ovens; allows COOK and microwave. |
D | Error will remain in the display until oven is repaired and powered back up. No error tones. |
E | Turning the oven off stops the error and flashing display. Can tweak away the error code. Error is redisplayed only if the selector is turned to CLEAN. |
F | Tweaking clears to “—“ for retry. |
G | Clears when the oven temperature is less then the runaway temperature with the selector switch off. |
H | Can be cancelled by tweaking if a good sensor is detected. |
I | Cleared with a mode change. |
J | Can be tweaked away for immediate retry. User must unlatch and delete the “—“ to try to relatch the door. |
K | Turns heat and microwave off. |
L | If two switches show a locked door, then E13 and LOCK are permanent in the display (in all modes). If the two switches show an open door, tweak away the E13 error message. |